Rather than a blog entry it is more like a note to myself.
And so I have managed to raise the bead on the rear tire of Jill (finally!).
(my last blog entry tells the tale of how defeated I was after the first try on the rear tire)
With that out of the way, I went on to perform the wheel balancing.
It is a DIY setup and I wouldn't even try to hide the fact that this balancing might only be good just for self satisfaction rather than bringing any actual benefit.
And this was my setup.
I recorded a 40 seconds clip on the actual procedure of balancing itself.
I later learned that this is what people describe as "static balancing", meaning the balance achieved in this setting is not good enough for actual riding.
I am quite OK with it anyhow because I don't have the equipment for dynamic balancing anyway.
Beggars can't be choosers I guess. :-)
This is the link to the video on youtube.
DIY Wheel Balancing on Honda Ape100
There are some lessons learned out of this tire change.
First, know the parts before taking apart the wheel assembly. I thought I knew, but it turned out that I lost the rear wheel collar. I am positive that I lost it (not something to brag about obviously) because the whole rear drum brake assembly just thumped out onto the ground when I removed the wheel from the axle. I didn't pay attention to what came out, and the price to pay is the losing of the part.
Second, do all relevant maintenance at one time.
I thought I wouldn't put in a fresh chain in this time but I was wrong. Turned out that the chain was so stiff and rusted I would want to change it.
Lastly, always budget more time and money than anticipated.
Yes, tools are always not enough, for a sunday mechanic like me.
Cheers,
CK
By 2023, I will embark on my own Long Way Round motorcycle trip. I am organizing my thoughts, documenting the preparations and motorcycle trips until 2023 on this blog.
Saturday, July 29, 2017
Sunday, July 23, 2017
Thoughts On Type Of Tires For Long Way Round
< Tube or Tubeless? >
I thought I have made up my mind about the choice of tires for the trip, but little did I know that I knew nothing about tires.
The tire changing on Jill (both front and rear) has given me some real experience and knowledge (however little that could be) in changing tires. I have always thought it would be a straightforward, like how one would go to the gas station, opens the fuel tank cap, pumps and pays then off you go. But no, things surely didn't work that way.
Then I went on and dismantle all that I had to. Nothing special here for I have been expecting the work after consulting the service manual. One thing caught me by surprise was how I had to use a steel rod to poke the rear axle out. Didn't think it would come to that. All in all everything was fine.
Dropping the bead was easy this time as I know where to put the levers on this time. As shown in the photo.
Managed to swap the tire on as well, without too much of a drama. Really experience is the only thing that counts, as I remember one of my bike buddies said.
But here's the thing. The photo on the left shows the side of a perfectly raised bead. On the right side, you can see that the bead was not equally raised along the sphere.
From another angle, I suppose everyone can tell that this tire might get the rider killed.
OK so much for the background information. This is a tubeless tire. To raise the bead I needed to get to the gas station and use the big capacity air compressor. For obvious reasons I couldn't get keep using their compressor so I had to go and get help, then come back and found out that it wasn't OK, then do some adjustments and go back again...
All this is very tiring and not very confidence inspiring.
And this is the issue - how do I change a tire if need be on the LWR trip without something that would create so much air pressure? I suppose there isn't any in the midst of Siberia.
There are people who says bead could be raised even with a hand pump. And I know by theory it should and could work. I tried that at home after two trips to the gas station. Maybe I need more practice, maybe my method was wrong, but it sure didn't work as I hoped it would be. (the pump did work though)
With a tube tire, I know for a fact that no air compressor is needed. (I haven't done any tire swapping but I have seen it in person in the past.) However, a tube tire tends to loose its pressure way faster than a tubeless tire in case of puncture, which could be very harmful for the rider.
I don't know. I think I still have plenty of time to think about this before I have to make a judgment call.
Cheers,
CK
I thought I have made up my mind about the choice of tires for the trip, but little did I know that I knew nothing about tires.
The tire changing on Jill (both front and rear) has given me some real experience and knowledge (however little that could be) in changing tires. I have always thought it would be a straightforward, like how one would go to the gas station, opens the fuel tank cap, pumps and pays then off you go. But no, things surely didn't work that way.
This was taken when changing the rear tire on Jill. I bought a bike jack which I didn't when doing the front tire. Lesson #1: a bike with center stand is certainly a bonus on the LWR trip.
Then I went on and dismantle all that I had to. Nothing special here for I have been expecting the work after consulting the service manual. One thing caught me by surprise was how I had to use a steel rod to poke the rear axle out. Didn't think it would come to that. All in all everything was fine.
Dropping the bead was easy this time as I know where to put the levers on this time. As shown in the photo.
Managed to swap the tire on as well, without too much of a drama. Really experience is the only thing that counts, as I remember one of my bike buddies said.
But here's the thing. The photo on the left shows the side of a perfectly raised bead. On the right side, you can see that the bead was not equally raised along the sphere.
From another angle, I suppose everyone can tell that this tire might get the rider killed.
OK so much for the background information. This is a tubeless tire. To raise the bead I needed to get to the gas station and use the big capacity air compressor. For obvious reasons I couldn't get keep using their compressor so I had to go and get help, then come back and found out that it wasn't OK, then do some adjustments and go back again...
All this is very tiring and not very confidence inspiring.
And this is the issue - how do I change a tire if need be on the LWR trip without something that would create so much air pressure? I suppose there isn't any in the midst of Siberia.
There are people who says bead could be raised even with a hand pump. And I know by theory it should and could work. I tried that at home after two trips to the gas station. Maybe I need more practice, maybe my method was wrong, but it sure didn't work as I hoped it would be. (the pump did work though)
With a tube tire, I know for a fact that no air compressor is needed. (I haven't done any tire swapping but I have seen it in person in the past.) However, a tube tire tends to loose its pressure way faster than a tubeless tire in case of puncture, which could be very harmful for the rider.
I don't know. I think I still have plenty of time to think about this before I have to make a judgment call.
Cheers,
CK
Thursday, July 6, 2017
Did the dealer bled my brake fluid properly?
< Air Bubble In Brake Reservoir? >
So the story goes like this:
I entrusted my beloved Lara to the dealer for the mandatory 12-month inspection. The bike went in good condition and the only changes done was the brake fluid change. The bike came out with a mushy front bike and I took this video and asked for opinion on Facebook.
Possible Air Bubble In Brake Reservoir?
I got opinions on both sides of the fence. However, the majority seems to think that the brake system wasn't bled in a proper way.
I have no way of telling if this is OK to accept, although I am riding the bike and I sure could brake faultlessly. However, just to be on the safe side, yes I will heed the opinion and go to the dealer to have them re-bled the whole thing.
Cheers,
CK
So the story goes like this:
I entrusted my beloved Lara to the dealer for the mandatory 12-month inspection. The bike went in good condition and the only changes done was the brake fluid change. The bike came out with a mushy front bike and I took this video and asked for opinion on Facebook.
Possible Air Bubble In Brake Reservoir?
I got opinions on both sides of the fence. However, the majority seems to think that the brake system wasn't bled in a proper way.
I have no way of telling if this is OK to accept, although I am riding the bike and I sure could brake faultlessly. However, just to be on the safe side, yes I will heed the opinion and go to the dealer to have them re-bled the whole thing.
Cheers,
CK
Sunday, July 2, 2017
Suzuki Bikes Test Ride Day
I remember my first time attending in a test ride event was with Honda. That was like some 10 years ago. Luck has it that Suzuki is coming somewhere nearby so I decided to went for a ride and while at it do some test rides as well.
Another angle at the reception booth. Notice the supply truck from Suzuki.
These were the booths for people to sit at while waiting for their turn at the bikes. They were organized by model. One model per line.
These were the bikes available for testing today. Apparently they didnt have the whole lineup for testing but there were enough bikes to grab my attention. My goal was to test ride the sub 250cc bikes. Not much interest for the larger bikes. (I already have one)
The much hyped V-Strom 250. Funny that they call it V-Strom because it isn't a V-Twin in her but a parallel twin. Anyway I can appreciate the marketing effort there. Given a chance I might even think of owning her.
This was a little stage prepared on the bed of a truck. The timetable says there would be talk show in between the test ride sessions but I didn't wait long enough to see that.
My choice of bikes. Gixxer 150 and the Burgman 200.
So this is how it works. Gotta go register at the receptionist by filling out a waiver form and showing the driver's license. Then each is issued with 3 coupons - one coupon per test ride. Use up all three and your time is up. (although the staff did approach me and asked me if I would like to get another three coupons upon finishing my turns.)
Bike pix. Damn just look at that Hayabusa. It has a 1.3 liter inline 4 under the seat. That's like a car!
And all the gixxers. The one on the right is the big gixxer and next to it is the small gixxer. I test rode the small gixxer as well.
Another angle. Really, I think the small gixxer works wonder. It's not fast by all standards but it is enough to move my soul.
Yes you got me I was trying to photo the lady in pink. Nothing weird about her but she seemed to be the only woman who displayed such intense interest in bike.
This is the Gixxer 150. I really liked it. Won't turn heads but good enough for me.
A far view of the course.
There were many people attending the test ride. All in all I would say I wouldn't just go for a test ride but would mix it with a ride day. Just too much hassle to go so far for a total of 9 minutes saddle time.
In my opinion this is how the foreign manufacturers beat the Japanese brands in their domestic market in the large bike segment. For harley and BMW, there isn't any regular test day like this one. But they let you test their bike anytime anyway and practically without limit. You can just go and blast for half an hour, go onto the highway if you like. Japanese manufacturers need to get better....
Cheers,
CK
Subscribe to:
Posts (Atom)